This camera was almost an impulse buy, when I saw it in the window of a camera shop at a giveaway price. However, I did not have the cash on me. As I carried on walking down the street I thought it would be snapped up by some lucky individual embarking on a film camera odyssey.
At the time, I did not realize it would be me six weeks later. On inspecting the MTL 3, the body was in mint condition - not a single mark on it that I could see. However it did have some issues, the most obvious one being that it had no lens, the light meter did not work and the foam on the film door had perished. Shouldn’t be too difficult to put right, I thought.
When I got the Praktica home, I tried to remove the battery cover, but it was locked solid. I did not have time to go any further with it at that point and thought that I could always use a hand held meter. With that, I put the camera in the cupboard.
Some weeks later I found myself going to the camera cupboard and picking up the Praktica. I had it in mind to get to the bottom of the stuck battery cover. I found a set of micro screwdrivers and undid the four screws that held the base plate on. I had no idea what I would find once the cover was removed. Fortunately, there were no springs that pinged out across the room when the base plate was lifted. I picked the battery housing off the base of the camera, only to be presented with a leaking battery - mystery solved.
Removing the aluminium battery cover from the metal insert was going to be a challenge. The battery had leaked into the threads, sticking the two parts together like super glue would. I don’t know what I was thinking when I squirted freeing oil on the thread and left it to sink in. I tried and failed to shift it using a fifty pence piece and a large adjustable spanner. There was no other course of action left to me but the brutality of fire and heat in a blow torch. I wondered if just heat would work?
As I walked across the room to the log stove, it was like walking into the sun. I left the battery housing on top of the log stove for five minutes or so and returned to the tropical room suitably dressed in shorts and, with heat resistant gloves, picked the battery cover off the stove. I placed the housing in the spanner and used the fifty pence piece in the cover and applied increasing amounts of pressure. With the sweat running down my face, it gave all of a sudden flicking the coin out of my fingers across the room. After I found the coin I placed it back in the slot and undid it as normal.
One issue down, three to go. The hunt was on to find a lens, battery and foam. I had forgotten what a waste of time looking for stuff on the net is. Some hours later, I had found a lens and battery (the modern number for it is LR9XP625G - the last three numbers are the most important). From the same place, I bought a Sigma 80-200 zoom lens. Thanks go to Bristol Cameras for their prompt and friendly service. The lens when it arrived was brand new and was the same price as the camera body.
I tracked down the foam to eBay and what a pain the seller was, to put it mildly. In the end I went down to a craft shop and picked up a sheet of foam for a pound - four times cheaper than the eBay seller!
With the light meter now working, the lens attached and the foam in place, it was time to load the camera with some film. I had an out of date roll of Fomapan 200, which is of a similar age to the camera, so that would do nicely.
Let the escapade begin.......It took a bit of time to get the film to wind on properly as I could now work out how the film lead picked up the wind on the cylinder. The sound and vibration from firing the shutter almost shocked it out of my hands. Must remember to grip it more firmly and use ear defenders.
To be fair, I had forgotten how basic the manufacture of this camera is and the sound of the shutter is quite reassuring. I don’t think I will be using it for candid street shots, but then again... It will take me a little time to get used to the way the camera is set up. It is a little chunky when making adjustments, but I will not let that put me off.
In case you missed part two here is the link part two
