How to load a plastic film sprial

This is an outline on how to load a film spiral ready for processing.

The only way to learn is to practice feeding a film onto a spiral in day light. I suggest purchasing a cheap roll of 35mm film, probably colour. It is also a good idea to have a brand new spiral to practice with. This should make the learning curve less steep as older spirals get temperamental the more they have been used.

Prepare the film: You can use a cassette opener or film retriever for 35mm. Once you have the leader/tongue of the film in view use a pair of scissors to cut it square. Then snip the corner off each side, the film is now ready for loading.

Now lay out everything you need on a table in daylight for a complete dummy run. Set the developing tank, lid, spiral with center in place and scissors out in the same order each time to get a picture in your mind's eye, this way you will know where everything is in the dark. Keep the film in your hand. With your eyes closed load the film on the spiral, place it in the developing tank, put the lid on and turn till it clicks shut. Some tanks have a screw top so be careful not to cross thread it. After a few practices you maybe ready to do it for real.

Note: Make sure your hands are clean and dry. Damp or sweaty fingers can cause problems with the loading of the film and leave marks on the processed negatives. It is a good idea to wear soft cotton gloves for protection.

Tip: If you wash your hands in cold water before you start it closes the pores reducing the need for gloves. It is also a good idea to earth yourself on a radiator to stop charging the film with static electricity therefore attracting dust. 

It is a lot easier to do than it sounds, so don't be put off. Everyone has their own way of doing this so if you have a tip to add please do.

This video gives a straight forward no-nonsense look at how it is done.

Trouble loading a plastic spiral.

The plastic Paterson type of spool can be difficult to load. A common problem is the little metal balls that grip the film get stuck. Dont try to force the film through, if you do it will kink the negative leaving a half-moon shape. It can make the frame(s) useless. You will need to part the spiral and start again. A pain I know! Be gentle when removing the film, there is a chance of damage.

Damp or wet spool will not load, so make sure it is completely dry before use. Sweaty, damp or sticky fingers will make it difficult as well.

A too tightly rolled up 35mm film in its cassette can take a set that makes it tricky to load. So when rewinding the film back into the case dont over wind it after you hear it has released itself from the camera spool. With practice it is possible to leave a little bit of the leader poking out.

Developing tanks.

There are a number of well-known makes to choose from. The most popular and widely used is the Patterson system. Another and maybe not so well known is the German maker Kaiser no lesser a system. So what are the differences? When buying a universal developing tank, if cost is one of your main considerations the Kaiser system wins hands down as being very good value for money. So much so its worth considering if you are thinking of buying a Paterson second-hand.

Both systems have good and bad points to consider. Starting at the top in both cases I have found no matter how well the cap has been put in place it leaks slightly when inverting the whole tank. It can be a messy annoyance when using PMK Pyro as it stains whatever it drips on too. Yes I know that each system comes with an agitator but the Paterson one is difficult to use because it is so thin, unlike Kaisers which has a top to it you can grip and when turned also moves the spiral up and down in the solution as well. Each company uses a different way to fix their lids. Paterson's idea is a twist and click method which I prefer but can be miss aligned if you are not careful. The Kaiser tank has a screw top which I have managed to cross thread each time.

The Kaisers spiral design is the main reason that I have one of their developing tanks. I'm having trouble with kinking the film when loading 120 format onto Paterson spirals and have used lots of different ideas to overcome it. The main difference with the Kaiser reel is that it has two large feed in wings where you load the film which makes loading a lot easier and faster with no kinking. Because of the trouble I've been having with the Kaiser screw top tank I now use a Paterson tank with the Kaiser reel, it is a little loose on the centre tube but the C clip stops it moving up and down when inverting. So for now I have the best of both worlds.