Over development

The film has been processed for longer than it needed. The following can cause this:

• Too long a development time.
• Too high a temperture. ( thermometers can go wrong.)
• Too much agitation.

Attention to these factors should avoid this. If you know that a film has been under exposed then you can remmedy it by over developing.

Maximum-energy developer

With this type of developer it is possible to double or treble the speed of a film. These developers promote an extremely strong response in the emulsion. They can increase the speed in a film that is too slow for the job. It can reliably produce a speed increase of up to three times with this pushed process. The big advantage with these developers is being able to keeping the grain fine and a good degree of sharpness. You need to be carefull when using them and follow the instructions. There are a couple of makes that have these attributes: Ilford Microphen and Promicrol.

How to load a plastic film sprial

This is an outline on how to load a film spiral ready for processing.

The only way to learn is to practice feeding a film onto a spiral in day light. I suggest purchasing a cheap roll of 35mm film, probably colour. It is also a good idea to have a brand new spiral to practice with. This should make the learning curve less steep as older spirals get temperamental the more they have been used.

Prepare the film: You can use a cassette opener or film retriever for 35mm. Once you have the leader/tongue of the film in view use a pair of scissors to cut it square. Then snip the corner off each side, the film is now ready for loading.

Now lay out everything you need on a table in daylight for a complete dummy run. Set the developing tank, lid, spiral with center in place and scissors out in the same order each time to get a picture in your mind's eye, this way you will know where everything is in the dark. Keep the film in your hand. With your eyes closed load the film on the spiral, place it in the developing tank, put the lid on and turn till it clicks shut. Some tanks have a screw top so be careful not to cross thread it. After a few practices you maybe ready to do it for real.

Note: Make sure your hands are clean and dry. Damp or sweaty fingers can cause problems with the loading of the film and leave marks on the processed negatives. It is a good idea to wear soft cotton gloves for protection.

Tip: If you wash your hands in cold water before you start it closes the pores reducing the need for gloves. It is also a good idea to earth yourself on a radiator to stop charging the film with static electricity therefore attracting dust. 

It is a lot easier to do than it sounds, so don't be put off. Everyone has their own way of doing this so if you have a tip to add please do.

This video gives a straight forward no-nonsense look at how it is done.

Fine grain developers

The production of fine grain in a negative is dependent on, in the first place, speed of the film and the choice of developer. The object is to keep the structure of the grain in the emulsion as small as possible so that it does not show up in the enlargments. Fine grain developers are best suited to films of medium speed about 125 ISO and above.

Some of the best known fine grain developers: Ilfords Microphen and ID11, Tetenal Ultrafin, Kodak D76, PMK Pyro is a staining developer that produces a fine grain and for the new grain techologies: Kodak HC110 and T max, Ilford LC29 and Tetenal Ultrafin plus, just to name a few.

Single shot developers.

One shot developers do what they say on the box! They are for single use and have a quality advantage over reusable ones, also removing the worries about usability. I know this may sound wasteful in these times of rising prices, but what cost do you apply for peace of mind when developing those precious negatives.

The advantages:

1. Fresh developer each time.
2. Ensures constant quality.
3. Consistant developing times.
4. No need to use replenisher.

In most cases these days most developers can be used as single shot, in the case of PMK Pyro and RO9 it is the only way.

What does developer do?

The function of the developer is to bring out the latent image held in the emulsion. This is achieved by a chemical reaction, acting on the silver, producing dark areas where it is light and bright areas where there is shadow. The negative is reversed later with the print. The two most important things to keep at the front of your mind are: the development time and the temperature. It is these two factors that ensure the ultimate image quality you later produce in the print. Too short a development time will produce too thin a negative, like wise too long a process time will make the negative too dence, leading to very short and very long print times.

Trouble loading a plastic spiral.

The plastic Paterson type of spool can be difficult to load. A common problem is the little metal balls that grip the film get stuck. Dont try to force the film through, if you do it will kink the negative leaving a half-moon shape. It can make the frame(s) useless. You will need to part the spiral and start again. A pain I know! Be gentle when removing the film, there is a chance of damage.

Damp or wet spool will not load, so make sure it is completely dry before use. Sweaty, damp or sticky fingers will make it difficult as well.

A too tightly rolled up 35mm film in its cassette can take a set that makes it tricky to load. So when rewinding the film back into the case dont over wind it after you hear it has released itself from the camera spool. With practice it is possible to leave a little bit of the leader poking out.